CVE-2026-54003

Kirby is an open-source content management system. Prior to 4.9.4 and from 5.4.4, Kirby sites with no configured user accounts that run on publicly accessible servers behind a reverse proxy setting the Forwarded, X-Client-IP, or X-Real-IP request header could allow remote attackers to install the Panel and create the first admin user because local-IP checks trusted those headers incorrectly. This issue is fixed in versions 4.9.4 and 5.4.4.

Kirby is an open-source content management system. Prior to 4.9.4 and from 5.4.4, Kirby sites with no configured user accounts that run on publicly accessible servers behind a reverse proxy setting the Forwarded, X-Client-IP, or X-Real-IP request header could allow remote attackers to install the Panel and create the first admin user because local-IP checks trusted those headers incorrectly. This issue is fixed in versions 4.9.4 and 5.4.4.

TL;DR

This vulnerability affects Kirby sites that have no configured user accounts and are running on publicly accessible servers behind a reverse proxy that sets the Forwarded: for=..., X-Client-IP, or X-Real-IP request header.

It was possible to install the Panel (= create the first admin user) in these setups even from remote IP addresses.

This vulnerability is of critical severity for affected sites.

Your site is not affected if any of the following apply:

• An admin account has already been configured
• The Panel and API are disabled
• The site is not running behind a reverse proxy
• The reverse proxy sets the X-Forwarded-For or Client-IP header instead of the affected ones.

Introduction

External Initialization is a type of vulnerability that allows attackers to initialize a system or configuration value without authentication.

This can give untrusted actors access to the system or let them control its behavior.

Affected components

The Kirby Panel and REST API are authenticated by local user accounts. If a Kirby installation does not yet have any users, it first needs to be installed. During the installation process, an initial admin user account is created.

To protect against external initialization attacks that would allow untrusted actors to create an admin user for the Kirby installation, Kirby already checked whether the current request came from a local IP address. This allows installing the Panel in local development setups. Installation on remote servers was only supposed to be possible when the panel.install configuration option was enabled.

The isLocal check takes all relevant request headers into account and treats a request as non-local as soon as any checked request header contains an external IP address.

Impact

In affected releases, the isLocal check for the installation logic did not properly take the Forwarded: for=... header into account. This header is set by modern reverse proxy servers. It also did not take into account the X-Client-IP or X-Real-IP headers, which are set by some custom reverse proxy setups.

This caused Kirby to falsely assume that an installation request was local and allowed creating an admin account even though the reverse proxy forwarded the request from an external IP address.

Reverse proxies setting the X-Forwarded-For or Client-IP headers were not affected. These headers were already properly checked for external IP addresses.

Patches

The problem has been patched in Kirby 4.9.4 and Kirby 5.4.4. Please update to one of these or a later version to fix the vulnerability.

In all of the mentioned releases, we fixed the isLocal check to also properly take Forwarded: for=..., X-Client-IP and X-Real-IP request headers into account.

Workarounds

Sites on older Kirby versions (Kirby 3 starting at 3.7.0) can be protected with one of the following workarounds:

• Perform the Panel installation yourself by creating an initial admin account. As soon as one or more accounts are present, the vulnerable installation code is no longer active.
• If you don't need the Panel, disable the REST API with the 'api' => false option in config.php.

Credits

Thanks to Peter Levashov (@petersevera) for responsibly reporting the identified issue.

Kirby is an open-source content management system. Prior to 4.9.4 and from 5.4.4, Kirby sites with no configured user accounts that run on publicly accessible servers behind a reverse proxy setting the Forwarded, X-Client-IP, or X-Real-IP request header could allow remote attackers to install the Panel and create the first admin user because local-IP checks trusted those headers incorrectly. This issue is fixed in versions 4.9.4 and 5.4.4.

Kirby is an open-source content management system. Prior to 4.9.4 and from 5.4.4, Kirby sites with no configured user accounts that run on publicly accessible servers behind a reverse proxy setting the Forwarded, X-Client-IP, or X-Real-IP request header could allow remote attackers to install the Panel and create the first admin user because local-IP checks trusted those headers incorrectly. This issue is fixed in versions 4.9.4 and 5.4.4.

TL;DR

This vulnerability affects Kirby sites that have no configured user accounts and are running on publicly accessible servers behind a reverse proxy that sets the Forwarded: for=..., X-Client-IP, or X-Real-IP request header.

It was possible to install the Panel (= create the first admin user) in these setups even from remote IP addresses.

This vulnerability is of critical severity for affected sites.

Your site is not affected if any of the following apply:

• An admin account has already been configured
• The Panel and API are disabled
• The site is not running behind a reverse proxy
• The reverse proxy sets the X-Forwarded-For or Client-IP header instead of the affected ones.

Introduction

External Initialization is a type of vulnerability that allows attackers to initialize a system or configuration value without authentication.

This can give untrusted actors access to the system or let them control its behavior.

Affected components

The Kirby Panel and REST API are authenticated by local user accounts. If a Kirby installation does not yet have any users, it first needs to be installed. During the installation process, an initial admin user account is created.

To protect against external initialization attacks that would allow untrusted actors to create an admin user for the Kirby installation, Kirby already checked whether the current request came from a local IP address. This allows installing the Panel in local development setups. Installation on remote servers was only supposed to be possible when the panel.install configuration option was enabled.

The isLocal check takes all relevant request headers into account and treats a request as non-local as soon as any checked request header contains an external IP address.

Impact

In affected releases, the isLocal check for the installation logic did not properly take the Forwarded: for=... header into account. This header is set by modern reverse proxy servers. It also did not take into account the X-Client-IP or X-Real-IP headers, which are set by some custom reverse proxy setups.

This caused Kirby to falsely assume that an installation request was local and allowed creating an admin account even though the reverse proxy forwarded the request from an external IP address.

Reverse proxies setting the X-Forwarded-For or Client-IP headers were not affected. These headers were already properly checked for external IP addresses.

Patches

The problem has been patched in Kirby 4.9.4 and Kirby 5.4.4. Please update to one of these or a later version to fix the vulnerability.

In all of the mentioned releases, we fixed the isLocal check to also properly take Forwarded: for=..., X-Client-IP and X-Real-IP request headers into account.

Workarounds

Sites on older Kirby versions (Kirby 3 starting at 3.7.0) can be protected with one of the following workarounds:

• Perform the Panel installation yourself by creating an initial admin account. As soon as one or more accounts are present, the vulnerable installation code is no longer active.
• If you don't need the Panel, disable the REST API with the 'api' => false option in config.php.

Credits

Thanks to Peter Levashov (@petersevera) for responsibly reporting the identified issue.