CVE-2026-87042

The IEEE 1588 (PTP) port implementation in subsys/net/lib/ptp/port.c adopted the logMessageInterval field of a received Delay_Resp message without any validation. port_delay_resp_msg_process() stored the raw wire value (a full-range int8_t) into port_ds.log_min_delay_req_interval, and that value is later used as a shift count by port_timer_set_timeout() when the Delay_Req timer is armed. Values below about -30 truncate the computed timeout to zero, and values with a magnitude of 64 or more perform an undefined shift of a uint64_t; the standards-defined "not applicable" encoding 0x7F fell into the latter case as well.

PTP messages are received over unauthenticated link-local traffic (UDP multicast on 224.0.1.129, IPv6 multicast, or raw IEEE 802.3), and the handler accepts a Delay_Resp from any sender as long as the port is a time receiver using the end-to-end delay mechanism and the message echoes the port identity and a pending sequence id — both of which the victim itself broadcasts in its Delay_Req. Any node on the same link can therefore inject a single crafted Delay_Resp, or simply become the time transmitter and advertise the bogus interval.

Once the delay timer is armed with a zero timeout, the cooperative PTP thread re-arms and retransmits a Delay_Req on every tick. Each transmission takes a buffer from the fixed CONFIG_PTP_MSG_POLL_SIZE message slab (default 10) and holds it on port->delay_req_list for three seconds, so the slab is emptied within milliseconds and ptp_msg_alloc() then blocks with K_FOREVER inside the only thread that frees those buffers — permanently stalling time synchronization until reboot. Where a transmit-timestamp callback on another thread keeps recycling buffers, the result is instead a sustained multicast Delay_Req flood and continuous CPU consumption. There is no memory corruption and no disclosure of data; the impact is availability of the PTP subsystem and of the local network segment.

The fix rejects intervals outside a representable range and treats 0x7F as "not applicable" as required by IEEE 1588-2019 Table 42. The equivalent unchecked adoption of logMessageInterval from Sync messages in port_sync_msg_process(), a weaker variant of the same issue, is fixed by the companion change 334bf57f416f (#118150), which applies the same range check, ignores the field for unicast Sync messages and treats 0x7F as not applicable.

The IEEE 1588 (PTP) port implementation in subsys/net/lib/ptp/port.c adopted the logMessageInterval field of a received Delay_Resp message without any validation. port_delay_resp_msg_process() stored the raw wire value (a full-range int8_t) into port_ds.log_min_delay_req_interval, and that value is later used as a shift count by port_timer_set_timeout() when the Delay_Req timer is armed. Values below about -30 truncate the computed timeout to zero, and values with a magnitude of 64 or more perform an undefined shift of a uint64_t; the standards-defined "not applicable" encoding 0x7F fell into the latter case as well.

PTP messages are received over unauthenticated link-local traffic (UDP multicast on 224.0.1.129, IPv6 multicast, or raw IEEE 802.3), and the handler accepts a Delay_Resp from any sender as long as the port is a time receiver using the end-to-end delay mechanism and the message echoes the port identity and a pending sequence id — both of which the victim itself broadcasts in its Delay_Req. Any node on the same link can therefore inject a single crafted Delay_Resp, or simply become the time transmitter and advertise the bogus interval.

Once the delay timer is armed with a zero timeout, the cooperative PTP thread re-arms and retransmits a Delay_Req on every tick. Each transmission takes a buffer from the fixed CONFIG_PTP_MSG_POLL_SIZE message slab (default 10) and holds it on port->delay_req_list for three seconds, so the slab is emptied within milliseconds and ptp_msg_alloc() then blocks with K_FOREVER inside the only thread that frees those buffers — permanently stalling time synchronization until reboot. Where a transmit-timestamp callback on another thread keeps recycling buffers, the result is instead a sustained multicast Delay_Req flood and continuous CPU consumption. There is no memory corruption and no disclosure of data; the impact is availability of the PTP subsystem and of the local network segment.

The fix rejects intervals outside a representable range and treats 0x7F as "not applicable" as required by IEEE 1588-2019 Table 42. The equivalent unchecked adoption of logMessageInterval from Sync messages in port_sync_msg_process(), a weaker variant of the same issue, is fixed by the companion change 334bf57f416f (#118150), which applies the same range check, ignores the field for unicast Sync messages and treats 0x7F as not applicable.

The IEEE 1588 (PTP) port implementation in subsys/net/lib/ptp/port.c adopted the logMessageInterval field of a received Delay_Resp message without any validation. port_delay_resp_msg_process() stored the raw wire value (a full-range int8_t) into port_ds.log_min_delay_req_interval, and that value is later used as a shift count by port_timer_set_timeout() when the Delay_Req timer is armed. Values below about -30 truncate the computed timeout to zero, and values with a magnitude of 64 or more perform an undefined shift of a uint64_t; the standards-defined "not applicable" encoding 0x7F fell into the latter case as well.

PTP messages are received over unauthenticated link-local traffic (UDP multicast on 224.0.1.129, IPv6 multicast, or raw IEEE 802.3), and the handler accepts a Delay_Resp from any sender as long as the port is a time receiver using the end-to-end delay mechanism and the message echoes the port identity and a pending sequence id — both of which the victim itself broadcasts in its Delay_Req. Any node on the same link can therefore inject a single crafted Delay_Resp, or simply become the time transmitter and advertise the bogus interval.

Once the delay timer is armed with a zero timeout, the cooperative PTP thread re-arms and retransmits a Delay_Req on every tick. Each transmission takes a buffer from the fixed CONFIG_PTP_MSG_POLL_SIZE message slab (default 10) and holds it on port->delay_req_list for three seconds, so the slab is emptied within milliseconds and ptp_msg_alloc() then blocks with K_FOREVER inside the only thread that frees those buffers — permanently stalling time synchronization until reboot. Where a transmit-timestamp callback on another thread keeps recycling buffers, the result is instead a sustained multicast Delay_Req flood and continuous CPU consumption. There is no memory corruption and no disclosure of data; the impact is availability of the PTP subsystem and of the local network segment.

The fix rejects intervals outside a representable range and treats 0x7F as "not applicable" as required by IEEE 1588-2019 Table 42. The equivalent unchecked adoption of logMessageInterval from Sync messages in port_sync_msg_process(), a weaker variant of the same issue, is fixed by the companion change 334bf57f416f (#118150), which applies the same range check, ignores the field for unicast Sync messages and treats 0x7F as not applicable.