CVE-2026-98530

In the Linux kernel, the following vulnerability has been resolved:

kprobes: Fix permanent hang when flushing the kprobe optimizer

Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build:

cd /sys/kernel/tracing

echo 'p:myprobe vfs_read+9' >> kprobe_events

echo 1 > events/kprobes/myprobe/enable

# wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED]

echo 0 > /proc/sys/debug/kprobes-optimization

INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246.

wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way.

Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first:

sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only

where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way.

Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.

In the Linux kernel, the following vulnerability has been resolved:

kprobes: Fix permanent hang when flushing the kprobe optimizer

Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build:

cd /sys/kernel/tracing

echo 'p:myprobe vfs_read+9' >> kprobe_events

echo 1 > events/kprobes/myprobe/enable

# wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED]

echo 0 > /proc/sys/debug/kprobes-optimization

INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246.

wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way.

Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first:

sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only

where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way.

Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.

In the Linux kernel, the following vulnerability has been resolved:

kprobes: Fix permanent hang when flushing the kprobe optimizer

Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build:

cd /sys/kernel/tracing

echo 'p:myprobe vfs_read+9' >> kprobe_events

echo 1 > events/kprobes/myprobe/enable

# wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED]

echo 0 > /proc/sys/debug/kprobes-optimization

INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246.

wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way.

Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first:

sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only

where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way.

Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.

In the Linux kernel, the following vulnerability has been resolved:

kprobes: Fix permanent hang when flushing the kprobe optimizer

Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build:

cd /sys/kernel/tracing

echo 'p:myprobe vfs_read+9' >> kprobe_events

echo 1 > events/kprobes/myprobe/enable

# wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED]

echo 0 > /proc/sys/debug/kprobes-optimization

INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246.

wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way.

Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first:

sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only

where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way.

Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.

In the Linux kernel, the following vulnerability has been resolved:

kprobes: Fix permanent hang when flushing the kprobe optimizer

Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build:

cd /sys/kernel/tracing

echo 'p:myprobe vfs_read+9' >> kprobe_events

echo 1 > events/kprobes/myprobe/enable

# wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED]

echo 0 > /proc/sys/debug/kprobes-optimization

INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246.

wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way.

Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first:

sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only

where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way.

Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.

In the Linux kernel, the following vulnerability has been resolved: kprobes: Fix permanent hang when flushing the kprobe optimizer Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build: # cd /sys/kernel/tracing # echo 'p:myprobe vfs_read+9' >> kprobe_events # echo 1 > events/kprobes/myprobe/enable # # wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED] # echo 0 > /proc/sys/debug/kprobes-optimization INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246. wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way. Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first: sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way. Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.

In the Linux kernel, the following vulnerability has been resolved: kprobes: Fix permanent hang when flushing the kprobe optimizer Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build: # cd /sys/kernel/tracing # echo 'p:myprobe vfs_read+9' >> kprobe_events # echo 1 > events/kprobes/myprobe/enable # # wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED] # echo 0 > /proc/sys/debug/kprobes-optimization INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246. wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way. Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first: sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way. Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.

Several security issues were discovered in the Linux kernel. An attacker could possibly use these to compromise the system. This update corrects flaws in the following subsystems:

• USB Gadget drivers;
• Memory management;
• Multiple devices driver;
• ARM64 architecture;
• EROFS file system;
• Networking core;
• eXpress Data Path;
• ARM32 architecture;
• M68K architecture;
• MIPS architecture;
• OpenRISC architecture;
• PA-RISC architecture;
• PowerPC architecture;
• RISC-V architecture;
• S390 architecture;
• User-Mode Linux (UML);
• x86 architecture;
• Block layer subsystem;
• Cryptographic API;
• Compute Acceleration Framework;
• Intel NPU Driver;
• Speakup Console Speech Driver;
• ACPI drivers;
• Serial ATA and Parallel ATA drivers;
• Auxiliary display drivers;
• Drivers core;
• Micron PCIe SSD driver;
• Null block device driver;
• Ublk userspace block driver;
• Compressed RAM block device driver;
• Bluetooth drivers;
• Bus devices;
• AMD CDX bus driver;
• Hardware random number generator core;
• Character device driver;
• TPM device driver;
• Clock framework and drivers;
• Clocksource drivers;
• CPU frequency scaling framework;
• CPU idle management framework;
• Hardware crypto device drivers;
• CXL (Compute Express Link) drivers;
• DAX dirext access to differentiated memory framework;
• DIBS (Direct Internal Buffer Sharing) drivers;
• Buffer Sharing and Synchronization framework;
• DMA engine subsystem;
• EDAC drivers;
• FireWire subsystem;
• ARM SCMI message protocol;
• ARM SCPI message protocol;
• Google firmware drivers;
• Qualcomm firmware drivers;
• FPGA Framework;
• GPIO subsystem;
• GPU drivers;
• HID subsystem;
• HSI subsystem;
• Microsoft Hyper-V drivers;
• Hardware monitoring drivers;
• CoreSight HW tracing drivers;
• I2C subsystem;
• I3C subsystem;
• IIO subsystem;
• InfiniBand drivers;
• Input Device core drivers;
• Input Device (Miscellaneous) drivers;
• Input Device (Mouse) drivers;
• On-Chip Interconnect management framework;
• IOMMU subsystem;
• Industry Pack bus drivers;
• IRQ chip drivers;
• Mailbox framework;
• Media drivers;
• MemoryStick subsystem;
• Multifunction device drivers;
• Analog Devices digital potentiometer driver;
• Broadcom VK accelerator driver;
• Fastrpc Driver;
• Amazon Nitro Secure Module driver;
• SGI GRU driver;
• MMC subsystem;
• MTD block device drivers;
• Network drivers;
• Ethernet bonding driver;
• Mellanox network drivers;
• Microsoft Azure Network Adapter (MANA) driver;
• STMicroelectronics network drivers;
• Texas Instruments network drivers;
• MediaTek network drivers;
• Near Field Communication (NFC) drivers;
• NTB driver;
• NVDIMM (Non-Volatile Memory Device) drivers;
• NVME drivers;
• Device tree and open firmware driver;
• Operating Performance Points (OPP) driver;
• PA-RISC drivers;
• PCI subsystem;
• Performance monitor drivers;
• PHY drivers;
• Pin controllers subsystem;
• Chrome hardware platform drivers;
• Mellanox platform drivers;
• Microsoft Surface platform drivers;
• x86 platform drivers;
• MediaTek PM domains;
• Power sequencing drivers;
• Power supply drivers;
• Powercap sysfs driver;
• PTP clock framework;
• PWM drivers;
• RapidIO drivers;
• Voltage and Current Regulator drivers;
• Remote Processor subsystem;
• MPAM driver;
• RPMSG subsystem;
• Real Time Clock drivers;
• S/390 drivers;
• SCSI subsystem;
• ASPEED SoC drivers;
• Samsung SoC drivers;
• SPI subsystem;
• small TFT LCD display modules;
• Greybus lights staging drivers;
• Media staging drivers;
• Realtek RTL8723BS SDIO drivers;
• TCM subsystem;
• Trusted Execution Environment drivers;
• Thermal drivers;
• Thunderbolt and USB4 drivers;
• TTY drivers;
• UFS subsystem;
• Userspace I/O drivers;
• USB DSL drivers;
• Cypress C67X00 USB…

Several security issues were discovered in the Linux kernel. An attacker could possibly use these to compromise the system. This update corrects flaws in the following subsystems:

• USB Gadget drivers;
• Memory management;
• Multiple devices driver;
• ARM64 architecture;
• EROFS file system;
• Networking core;
• eXpress Data Path;
• ARM32 architecture;
• M68K architecture;
• MIPS architecture;
• OpenRISC architecture;
• PA-RISC architecture;
• PowerPC architecture;
• RISC-V architecture;
• S390 architecture;
• User-Mode Linux (UML);
• x86 architecture;
• Block layer subsystem;
• Cryptographic API;
• Compute Acceleration Framework;
• Intel NPU Driver;
• Speakup Console Speech Driver;
• ACPI drivers;
• Serial ATA and Parallel ATA drivers;
• Auxiliary display drivers;
• Drivers core;
• Micron PCIe SSD driver;
• Null block device driver;
• Ublk userspace block driver;
• Compressed RAM block device driver;
• Bluetooth drivers;
• Bus devices;
• AMD CDX bus driver;
• Hardware random number generator core;
• Character device driver;
• TPM device driver;
• Clock framework and drivers;
• Clocksource drivers;
• CPU frequency scaling framework;
• CPU idle management framework;
• Hardware crypto device drivers;
• CXL (Compute Express Link) drivers;
• DAX dirext access to differentiated memory framework;
• DIBS (Direct Internal Buffer Sharing) drivers;
• Buffer Sharing and Synchronization framework;
• DMA engine subsystem;
• EDAC drivers;
• FireWire subsystem;
• ARM SCMI message protocol;
• ARM SCPI message protocol;
• Google firmware drivers;
• Qualcomm firmware drivers;
• FPGA Framework;
• GPIO subsystem;
• GPU drivers;
• HID subsystem;
• HSI subsystem;
• Microsoft Hyper-V drivers;
• Hardware monitoring drivers;
• CoreSight HW tracing drivers;
• I2C subsystem;
• I3C subsystem;
• IIO subsystem;
• InfiniBand drivers;
• Input Device core drivers;
• Input Device (Miscellaneous) drivers;
• Input Device (Mouse) drivers;
• On-Chip Interconnect management framework;
• IOMMU subsystem;
• Industry Pack bus drivers;
• IRQ chip drivers;
• Mailbox framework;
• Media drivers;
• MemoryStick subsystem;
• Multifunction device drivers;
• Analog Devices digital potentiometer driver;
• Broadcom VK accelerator driver;
• Fastrpc Driver;
• Amazon Nitro Secure Module driver;
• SGI GRU driver;
• MMC subsystem;
• MTD block device drivers;
• Network drivers;
• Ethernet bonding driver;
• Mellanox network drivers;
• Microsoft Azure Network Adapter (MANA) driver;
• STMicroelectronics network drivers;
• Texas Instruments network drivers;
• MediaTek network drivers;
• Near Field Communication (NFC) drivers;
• NTB driver;
• NVDIMM (Non-Volatile Memory Device) drivers;
• NVME drivers;
• Device tree and open firmware driver;
• Operating Performance Points (OPP) driver;
• PA-RISC drivers;
• PCI subsystem;
• Performance monitor drivers;
• PHY drivers;
• Pin controllers subsystem;
• Chrome hardware platform drivers;
• Mellanox platform drivers;
• Microsoft Surface platform drivers;
• x86 platform drivers;
• MediaTek PM domains;
• Power sequencing drivers;
• Power supply drivers;
• Powercap sysfs driver;
• PTP clock framework;
• PWM drivers;
• RapidIO drivers;
• Voltage and Current Regulator drivers;
• Remote Processor subsystem;
• MPAM driver;
• RPMSG subsystem;
• Real Time Clock drivers;
• S/390 drivers;
• SCSI subsystem;
• ASPEED SoC drivers;
• Samsung SoC drivers;
• SPI subsystem;
• small TFT LCD display modules;
• Greybus lights staging drivers;
• Media staging drivers;
• Realtek RTL8723BS SDIO drivers;
• TCM subsystem;
• Trusted Execution Environment drivers;
• Thermal drivers;
• Thunderbolt and USB4 drivers;
• TTY drivers;
• UFS subsystem;
• Userspace I/O drivers;
• USB DSL drivers;
• Cypress C67X00 USB…